An airbag deploys within milliseconds. Anyway, I pulled the two seat belt wires drivers side from the yellow harness and connected them together. Restraint system contains many components. There are also 3 different fuse boxes in your vehicle. My indy says this has been a common problem and has repaired many cars by just doing some work on the wires under the seat. This sounds hard but the back of the fuse board is big enough to get your hand through We then pulled the 2nd part of the same loom from which feeds the ignition, lights and instrument cluster through towards the right of the van so we could fix the length that runs from the radio hole and behind the instrument cluster.
The airbag controller passes self test. In particular, work relevant to safety or on safety-related systems must be carried out at a qualified specialist workshop. I have a 1996 W210 E320. Suck it up with a strong vacuum cleaner. Do not route the belt strap across sharp-edged or fragile objects, especially if these are on or in your clothing, e. What is the srs light that is illuminated on my dash all about the acronym srs stands for supplemental restraint system which is the proper name for the airbag system in your vehicle this is the dash warning light that.
Could you give me a little direction from here? Inside the floor mounted seat belt clasp there is a small contact switch, if this has sand, debris, dirt or drink spill in there it will give a bad connection. Feel like getting ripped off at Mercedes. The triggering thresholds for the belt tensioners and airbags are variable and are adapted to the rate of vehicle deceleration. After the airbags have been triggered, they must be replaced at a qualified specialist workshop which has the necessary specialist knowledge and tools to carry out the work required. Mercedes-Benz recommends that you use a Mercedes-Benz Service Centre for this purpose. That is not fairly reflected in their claimed invoice value if I have calculated the exchange rate correctly. I hope that is of some help, All the best Steve Hi Mohit, If the code is the 9030 code, it is with regard to the tele-aid system.
I am pretty sure that there is a box you can get that interfaces between the six disc and the head unit enabling an alternative input. All the best Steve Hi Steve On the Ball You really seem to have all the solutions, perhaps you can help me. If the electric sliding door is secured, only the sliding door rear controls are deactivated. It forms part of the seat occupancy circuit. I turned off the battery in an attempt to clean the system. Than I have the erors again in the dash. Neither seat belts nor airbags generally provide any protection from objects that enter the vehicle.
Check the plug see if anything has knocked it and wiggle to make sure connected correctly. Sorry for the late reply the message somehow found its way into the site spam box — now rectified! Best regards Hey brather again thanx very much for answer, about sentral getway am get new according vin then i will give the code number might am wrong when i bayed cuse the dealar he said i have other code simillar my get way the number of old one its W211 540 56 45 then new one its A169 540 69 45 am tired really cuse i have the car without benafit so let me i tallk with you about the things not working after the dammege 1 draiver seats not moving for all way but miror still work. Tays realty auction auction 2018 mtfcu vehicle auction item click on any picture to see a larger image. Would you have any clue what would cause the errors or how to fix them? Best wishes Noor Hi Steve, Thanks for all the nice write-ups. Thank you very much for a lightning fast response — Wow! Ensure all the cabling is connected from the explosive device on the retractor and correct mating of all under seat wiring. Airbags do not replace the need for all vehicle occupants to wear their seat belt correctly at all times.
Serious srs restraint system malfunction pls help mbworldorg forums serious srs restraint system malfunction pls help6402657full. It is possible that you think the plug is inserted and latched correctly but actually it is only half way connected. When the vehicle occupant makes contact with the airbag, hot gas flows out of the deployed airbag. These systems are sensitive to voltage. This should give you some vital clues as throwing parts and labour at the job without this is really financial suicide! Hope this helps a little. The clasp is glued together, the switch is inside so that pretty much scuppers any dismantling and cleaning.
The most common fault is failure of the seat pad wiring or the thin wires that connect to it and pass through the upholstery to connect to it. Comply with safety regulations when disposing of belt tensioners. It should be possible to competently repair a few cut wires in a couple of hours at the most. Give them a good clean inside as best you can vacuum and blunt table knife they get all sorts inside! Not all airbags are deployed in an accident. A small amount of powder is released when an airbag is deployed. Only adjust the belt height when the vehicle is stationary and the parking brake is applied.
A friend of mine informed me that the car does not start for safety reasons since the malfunction of the airbag can bring danger to the occupant. The dash is in 2 halves the upper and lower, just as you say the glove box is moulded into the lower half. The van was drivable, but the brake lights were always on ans it blew a 7. Thanks Ok I have just heard back from the dealership, they have diagnosed the issues, apprantly its a wiring defect? You can also open the window to allow fresh air to enter the interior. The powder does not constitute a health hazard and does not indicate that there is a fire in the vehicle. Seat Occupied - Airbag's Enabled Prior to buying Airbag360 passenger occupancy sensor emulator please make sure Your car was correctly diagnosed. Thanks Madison2 I will check the car tonight.
Check the plug see if anything has knocked it and wiggle to make sure connected correctly. At this time the car is in the parking area of a supermarket and will spend the night there. The loom passes between two metal plates that support the steering column and they had worn through one of the power wires going to the instrument cluster. If so it sounds like it has become disconnected somehow or is faulty. Avoid seat positions that prevent the seat belt from being correctly routed. Installation can be completed in 3 simple steps. You will have to carefully clean them out with a stiff paintbrush and vacuum cleaner, then spray electrical contact switch cleaner into the buckle aperture while latching and unlatching the belt.